Common Questions and Answers about Fentanyl gel patch. A matrix fentanyl patch places the fentanyl in adhesive. HOSPICE left the 'death kit' which includes a couple Fentanyl Patches. Don't ever smoke the gel in a. Well I have a good connection for sandoz gel 100s recently. My own guide on extracting non- gel fentanyl patches : opiates. The following method is rarely mentioned due to the massive overdose potential of people who IV the extract, but this is how you can smoke the non- gel fent patches with relative safety. I will not include the step you need to take to IV the final product, but either way, PLEASE don't!! Even small differences in your technique each time you do this can cause enough variation to result in OD when you IV the extract, and it is plain insane to try to IV your first ever extract. PLEASE DON'T IV THIS STUFF. How to smoke fentanyl patches safely (non gel. Once the patch is cut the fentanyl can not leak out if they are non gel patches. SWIY could cut the patch in. How to Not Remove Fentanyl From Patches. What I really wish to know though is quite simple I suppose; can the Fentanyl within the patch be safely removed. The regular patch contains a gel that can be abused even by smoking it. Why do I have the constant smell of smoke in my nose. Fentanyl Abuse Prevention – A Shared Responsibility Ontario. Fentanyl 100 mg non-gel patch and cut it into 1/4's.Jun 3. EDIT: Forgot to place this warning. High concentration alcohol produce flammable vapors when heated (duh), so please no smoking, no open flames, keep well ventilated, and preferably do this outside. You do not want to spill and start a fire, so please do not do this while nodding. Be CAREFUL! Get the most concentrated ISO alcohol you can, some pure ETOH (ethanol) if possible, a smooth glass surface to evaporate on, a small glass container (stainless steel is fine), a metal pot, an electric heating element (no open flames). Optionally, a hair dryer and pipette. What you need to do is as follows. Place your patches inside a small container of ISO alcohol for 2. This will dissolve the glue slightly without extracting a significant portion of the fent contained in the plastic matrix. Remove the glue with your fingers. You should be able to easily scratch off the glue by placing the patch on a hard surface, scratch, and the glue will come off in stretchy chunks. If you find it difficult, give it 5- 1. Now you need to set up a double boiler. How to smoke mylan fentanyl patch How to smoke mylan fentanyl patch 2.16.262 pour Android. I have a straw that I used to smoke a mylan fentanyl sticker non gel one I. Smoking apotex fentanyl non-gel patches? So swim has procured a 100mcg an hour fentanyl patch. Don't smoke the non-gel. I prefer to use a glass dish that is sitting on top of chopsticks inside a small metal pot filled with water. Fill the glass dish with ISO, and bring the water temperature up such that you are getting slight boiling action in the ISO. If you have pure ethanol, mix this into the ISO for better yield (my subjective experience only), but only if you have high concentration ethanol (no vodka). I will refer to this mix as simply ISO from this point on. Place the PLASTIC portion of your patches in the ISO filled glass plate in your double boiler setup. Depending on the size of your double boiler, you may need to cut your larger (1. Many people seem to think that the good stuff is in the glue, but this is not true. The actual fent is locked within the plastic matrix of the patch. The heat will cause the fent to be released rather quickly, in the same way that applying a hand warmer to your a worn patch speeds up the release, while the alcohol acts as a very efficient medium to transfer the released fent as it is easily evaporated later. Allow the alcohol to bubble for at least an hour. I prefer 9. 0- 1. Do not allow the ISO boiling to get too intense, as this will cause spilling into the water portion of the double boiler (causing unrecoverable loss). Note that the drops of liquid ISO spilling over from too intense of a boil will be tiny and almost invisible, but is significant. During this process, you will need to watch your double boiler and add more alcohol constantly as it boils away. You should make sure that the water in the bottom half of the setup NEVER gets to the point of boiling. Do not throw these away. I soak them inside another container of ISO where I collect all my extracted patches. This container of extracted patches has saved me in tight situations. Now continue allowing the alcohol to boil off until very little remains, but be very careful to make sure that you do NOT dry it out. Pull the remaining liquid into a pipette (preferred) and dump it onto a glass surface. Depending on how much fent you have in the solution, the liquid will be tinged yellow when pulled into the pipette. Personally, I prefer to have 2ml of liquid at this stage per my usual run of 2x. With your hairdryer running on a warm/cool setting (not uncomfortable for your skin at 1inch distance directly blowing on your hand), push the liquid around on the glass. If the liquid lacks viscosity and bead on the glass with low air flow, you did something wrong, most likely that you did not allow enough ISO to boil off. It should stay in a puddle shape and seemingly form a slight . This process is hard to describe, but you are trying to push the ISO fent concentrate around such that it dries as a large patch/film on the glass. I like to drip small puddles with the pipette, and make 2x. After the fent is dried, leave it on the glass, and scrape small sections with a razor for use. Depend on how thick it dried, I scrape 1/2. It will look like a white film, somewhat plastic like in consistency. Smoke this and for the love of god do not shoot it. Please Please Please do NOT shoot this shit. Due to differences in ISO/ETOH concentration, how well your technique is, your temp control, the potency CAN VARY WILDLY. After I had my technique down, I was able to get very consistent quality, but even then I was afraid of shooting this shit. The fent in its current form will be somewhat difficult to dissolve in water for shooting anyway, and I will not instruct on how to prepare for IV. When smoked, a bit the size of a quarter of a match head will get me good. This was when I was smoking/shooting 2 packs (1. So. Cal balloons of tar/pack ~1gram/pack) per day. I would estimate a single 1. In terms of how long it lasts, perhaps putting the patch on your skin is better. In terms of intensity, it is FAR more intense than any smoked heroin, and a large hit is more intense than a injection. However, I would still prefer a shot due to the addictive nature of the prep/and the feel of the shot itself, though that is another topic all by itself. In terms of actual yield, I think it was well worth it. I was doing this weekly when I got my hands on patches. Oh, remember the extracted patches you saved and placed together into its own ISO container? Well once you have collected a few patches in there and after they have been soaking for a day or two, just boil down the alcohol in the same double boiler setup. This will get you a hit or two, if you did the above extraction correctly, or lots of hits if you didn't and left a bunch of fent in the used up patches. For those who will say that the heat destroys the fent, I must say that I had no objective way to verify my percent yield. However, in my subjective experience, the temperature the 9. ISO/ETOH solution boils at should not degrade the active ingredient significantly in 9. If one is too concerned about this, simply soak the patches in alcohol without heat, and allow the ISO to evaporate naturally (a 2. I have tried the cold method, and I got less product in addition to the agonizing wait. TLDR: remove glue, boil in alcohol, evaporate alcohol, scrape up, smoke, do NOT inject.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
December 2016
Categories |